Planet MGSW-28240F Uživatelský manuál

User’s Manual of MGSW-28240F 1

User’s Manual of MGSW-28240F 6.3 Port Management Command...

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Check to delete the entry. It will be deleted during the nex

User’s Manual of MGSW-28240F A string identifying the view name that this entry should belong to. The allowed string length is 1 to 32, and the allow

User’s Manual of MGSW-28240F A string identifying the group name that this entry should belong to. The allowed string length is 1 to 32, and the allo

User’s Manual of MGSW-28240F 4.4 Port Management Use the Port Menu to display or configure the Managed Switch's ports. This section has the foll

User’s Manual of MGSW-28240F The page includes the following fields: Object Description This is the logical port number for this row, * means select

User’s Manual of MGSW-28240F  Disabled: All power savings mechanisms disabled.  ActiPHY: Link down power savings enabled.  PerfectReach: Link u

User’s Manual of MGSW-28240F 4.4.2 Port Statistics Overview This page provides an overview of general traffic statistics for all switch ports. The

User’s Manual of MGSW-28240F Buttons : Click to refresh the page immediately. : Clears the counters for all ports. Auto-refresh : Check this box t

User’s Manual of MGSW-28240F  Rx and Tx Broadcast The number of received and transmitted (good and bad) broadcast packets. A count of the MAC Contr

User’s Manual of MGSW-28240F Buttons : Click to refresh the page immediately. : Clears the counters for all ports. Auto-refresh : Check this box t

User’s Manual of MGSW-28240F VLAN Name Delete ...

User’s Manual of MGSW-28240F  1000Base-LX  100Base-FX Display the speed of current SFP module. The speed value or description is gotten from the

User’s Manual of MGSW-28240F Figure 4-4-5: Port Mirror Application The traffic to be copied to the mirror port is selected as follows:  All fram

User’s Manual of MGSW-28240F Figure 4-4-6: Mirror Configuration Page Screenshot 112

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Port to mirror also known as the mirror port. Frames from po

User’s Manual of MGSW-28240F The device supports the following Aggregation links :  Static LAGs (Port Trunk) – Force aggregared selected ports to b

User’s Manual of MGSW-28240F  The ports that can be assigned to the same link aggregation have certain other restrictions (see below).  Ports can

User’s Manual of MGSW-28240F 116 4.5.1 Static Aggregation This page is used to configure the Aggregation hash mode and the aggregation group. The a

User’s Manual of MGSW-28240F Static Aggregation Group Configuration The Aggregation Group Configuration screen in Figure 4-5-3 appears. Figure 4-5-3

User’s Manual of MGSW-28240F 4.5.2 LACP Configuration Link Aggregation Control Protocol (LACP) - LACP LAG negotiate Aggregated Port links with other

User’s Manual of MGSW-28240F Figure 4-5-4 : LACP Port Configuration Page Screenshot 119

User’s Manual of MGSW-28240F Security Switch SNMP Trap Destination...

User’s Manual of MGSW-28240F The page includes the following fields: Object Description The switch port number, * means selection of all ports of Ma

User’s Manual of MGSW-28240F Figure 4-5-5: LACP System Status Page Screenshot The page includes the following fields: Object Description  Aggr I

User’s Manual of MGSW-28240F Figure 4-5-6: LACP Status Page Screenshot The page includes the following fields: Object Description The switch port

User’s Manual of MGSW-28240F The partners System ID (MAC address).  Partner System ID The partner port number connected to this port.  Partner Po

User’s Manual of MGSW-28240F Object Description The switch port number.  Port Shows how many LACP frames have been sent from each port.  LACP Re

User’s Manual of MGSW-28240F 4.6 VLAN 4.6.1 VLAN Overview A Virtual Local Area Network (VLAN) is a network topology configured according to a logical

User’s Manual of MGSW-28240F 4.6.2 IEEE 802.1Q VLAN In large networks, routers are used to isolate broadcast traffic for each subnet into separate

User’s Manual of MGSW-28240F - Untagging - The act of stripping 802.1Q VLAN information out of the packet header. 802.1Q VLAN Tags The figure be

User’s Manual of MGSW-28240F Port VLAN ID Packets that are tagged (are carrying the 802.1Q VID information) can be transmitted from one 802.1Q com

User’s Manual of MGSW-28240F VLAN Classification When the switch receives a frame, it classifies the frame in one of two ways. If the frame is u

User’s Manual of MGSW-28240F Security Network Psec Port...

User’s Manual of MGSW-28240F Display the current number of VLANs  Current number of VLANs Display the VLAN learning mode. The Managed Switch suppor

User’s Manual of MGSW-28240F 131 QinQ tunneling is used to maintain customer-specific VLAN and Layer 2 protocol configurations even when different

User’s Manual of MGSW-28240F VLAN Port Configuration The VLAN Port Configuration screen in Figure 4-6-2 appears. Figure 4-6-2 : VLAN Port Configurat

User’s Manual of MGSW-28240F The page includes the following fields: Object Description This is the logical port number for this row.  Port  PV

User’s Manual of MGSW-28240F The port must be a member of the same VLAN as the Port VLAN ID. Buttons : Click to save changes. : Click to undo any c

User’s Manual of MGSW-28240F entries or it can be added to the new entries. A row of check boxes for each port is displayed for each VLAN ID. To incl

User’s Manual of MGSW-28240F Figure 4-6-4: VLAN Membership Status for Static User Page Screenshot The page includes the following fields: Object D

User’s Manual of MGSW-28240F : Select VLAN Users from this drop down list. Auto-refresh : Check this box to enable an automatic refresh of the page a

User’s Manual of MGSW-28240F The page includes the following fields: Object Description The logical port for the settings contained in the same row.

User’s Manual of MGSW-28240F 4.6.8 Private VLAN The Private VLAN membership configurations for the switch can be monitored and modified here. Private

User’s Manual of MGSW-28240F Security Network DHCP Snooping Port Mode...

User’s Manual of MGSW-28240F : Click to refresh the page immediately. 4.6.9 Port Isolation Overview When a VLAN is configured to be a private VLAN,

User’s Manual of MGSW-28240F  Isolated ports — Ports from which traffic can only be forwarded to promiscuous ports in the private VLAN — Ports whic

User’s Manual of MGSW-28240F 4.6.10.1 Two separate 802.1Q VLANs The diagram shows how the Managed Switch handles Tagged and Untagged traffic flow f

User’s Manual of MGSW-28240F  Tagged packet entering VLAN 2 5. While [PC-3] transmits a tagged packet with VLAN Tag=2 enters Port-3, [PC-1] and [P

User’s Manual of MGSW-28240F 144 It’s important to remove the VLAN members from VLAN 1 configuration. Or the ports would become overlap setting. (

User’s Manual of MGSW-28240F 4.6.10.2 VLAN Trunking between two 802.1Q aware Switches The most cases are used for “Uplink” to other switches. VLANs

User’s Manual of MGSW-28240F 146 1. Specify Port-8 to be the 802.1Q VLAN Trunk port. 2. Assign Port-8 to both VLAN 2 and VLAN 3 on the VLAN Member

User’s Manual of MGSW-28240F 4.6.10.3 Port Isolate The diagram shows how the Managed Switch handles isolate and promiscuous ports, and the each PC is

User’s Manual of MGSW-28240F Figure 4-6-16: Private VLAN Port Setting 4.6.11 MAC-based VLAN The MAC-based VLAN entries can be configured here. Thi

User’s Manual of MGSW-28240F : Click to undo any changes made locally and revert to previously saved values. Auto-refresh : Check this box to refresh

User’s Manual of MGSW-28240F STP Port AutoEdge ...

User’s Manual of MGSW-28240F 4.6.13 IP Subnet-based VLAN This page allows for adding, updating and deleting IP subnet-based VLAN entries and assignin

User’s Manual of MGSW-28240F 4.6.14 Protocol-based VLAN This page allows you to add new protocols to Group Name (unique for each Group) mapping entri

User’s Manual of MGSW-28240F a.OUI: OUI (Organizationally Unique Identifier) is value in format of xx-xx-xx where each pair (xx) in string is a hexad

User’s Manual of MGSW-28240F The page includes the following fields: Object Description To delete a Group Name to VLAN map entry, check this box. Th

User’s Manual of MGSW-28240F 4.7 Spanning Tree Protocol 4.7.1 Theory The Spanning Tree protocol can be used to detect and disable network loops, and

User’s Manual of MGSW-28240F  The port identifier of the transmitting port The switch sends BPDUs to communicate and construct the spanning-tree to

User’s Manual of MGSW-28240F  From disabled to blocking Figure 4-7-1: STP Port State Transitions You can modify each port state by using managemen

User’s Manual of MGSW-28240F The following are the user-configurable STP parameters for the switch level: Parameter Description Default Value Brid

User’s Manual of MGSW-28240F Port priority 128 Port cost 0 Bridge Priority 32,768 User-Changeable STA Parameters The Switch’s factory default set

User’s Manual of MGSW-28240F STP breaks the loop by blocking the connection between switch B and C. The decision to block a particular connection is

User’s Manual of MGSW-28240F LLDP MED Configuration ...

User’s Manual of MGSW-28240F In this example, only the default STP values are used. Figure 4-7-3: After Applying the STA Rules The switch with th

User’s Manual of MGSW-28240F ‧ Extension – Multiple Spanning Tree Protocol (MSTP) : Defines an extension to RSTP to further develop the usefulness o

User’s Manual of MGSW-28240F  Max Age The maximum age of the information transmitted by the Bridge when it is the Root Bridge. Valid values are in

User’s Manual of MGSW-28240F 4.7.3 Bridge Status This page provides a status overview for all STP bridge instances. The displayed table contains a ro

User’s Manual of MGSW-28240F Figure 4-7-6 : STP CIST Port Configuration Page Screenshot 164

User’s Manual of MGSW-28240F The page includes the following fields: Object Description The switch port number of the logical STP port.  Port Cont

User’s Manual of MGSW-28240F administrator to prevent bridges external to a core region of the network, causing address flushing in that region, poss

User’s Manual of MGSW-28240F Port Type Link Type IEEE 802.1w-2001 Ethernet Half Duplex Full Duplex Trunk 2,000,000 1,000,000 500,000 Fast

User’s Manual of MGSW-28240F bridge priority plus the MSTI instance number, concatenated with the 6-byte MAC address of the switch forms a Bridge Ide

User’s Manual of MGSW-28240F 169 4.7.6 MSTI Configuration This page allows the user to inspect the current STP MSTI bridge instance priority confi

User’s Manual of MGSW-28240F QoS DSCP Classification Mode ...

User’s Manual of MGSW-28240F The page includes the following fields: Configuration Identification Object Description  Configuration Name The name

User’s Manual of MGSW-28240F The page includes the following fields: MSTI Port Configuration Object Description Select the bridge instance and set m

User’s Manual of MGSW-28240F Figure 4-7-10: MST1 MSTI Port Configuration Page Screenshot 172

User’s Manual of MGSW-28240F The page includes the following fields: MSTx MSTI Port Configuration Object Description The switch port number of the

User’s Manual of MGSW-28240F Figure 4-7-11: STP Port Status Page Screenshot The page includes the following fields: Object Description The switch

User’s Manual of MGSW-28240F  Forwarding  Non-STP The time since the bridge port was last initialized.  Uptime Buttons Auto-refresh : Check

User’s Manual of MGSW-28240F 176 : Click to refresh the page immediately. : Click to clear the information immediately.

User’s Manual of MGSW-28240F 4.8 Multicast 4.8.1 IGMP Snooping The Internet Group Management Protocol (IGMP) lets host and routers share information

User’s Manual of MGSW-28240F Figure 4-8-2: Multicast Flooding Figure 4-8-3: IGMP Snooping Multicast Stream Control 178

User’s Manual of MGSW-28240F IGMP Versions 1 and 2 Multicast groups allow members to join or leave at any time. IGMP provides the method for members

User’s Manual of MGSW-28240F MVR Groups...

User’s Manual of MGSW-28240F message, and query messages that are specific to a given group. The states a computer will go through to join or to leav

User’s Manual of MGSW-28240F 4.8.2 IGMP Snooping Configuration This page provides IGMP Snooping related configuration. The IGMP Snooping Configuratio

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Enable the Global IGMP Snooping.  Snooping Enabled  Unr

User’s Manual of MGSW-28240F 4.8.3 IGMP Snooping VLAN Configuration Each page shows up to 99 entries from the VLAN table, default being 20, selected

User’s Manual of MGSW-28240F represented by the Last Member Query Interval, multiplied by the Last Member Query Count. The allowed range is 0 to 31

User’s Manual of MGSW-28240F Figure 4-8-7: IGMP Snooping Port Group Filtering Configuration Page Screenshot The page includes the following fields:

User’s Manual of MGSW-28240F Figure 4-8-8: IGMP Snooping Status Page Screenshot The page includes the following fields: Object Description The VLA

User’s Manual of MGSW-28240F  V1 Reports Received The number of Received V1 Reports.  V2 Reports Received The number of Received V2 Reports.  V

User’s Manual of MGSW-28240F : Click to refresh the page immediately> : Updates the table, starting with the first entry in the IGMP Group Table.

User’s Manual of MGSW-28240F Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Cl

User’s Manual of MGSW-28240F IPMC Filtering...

User’s Manual of MGSW-28240F Figure 4-8-11: MLD Snooping Configuration Page Screenshot The page includes the following fields: Object Description E

User’s Manual of MGSW-28240F Figure 4-8-12: IGMP Snooping VLAN Configuration Page Screenshot The page includes the following fields: Object Descri

User’s Manual of MGSW-28240F range is 0 to 31744 seconds, default unsolicited report interval is 1 second. Buttons : Refreshes the displayed table s

User’s Manual of MGSW-28240F The logical port for the settings.  Port The IP Multicast Group that will be filtered.  Filtering Group Buttons : C

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  VLAN ID of the entry. The VLAN ID  Querier Version rren

User’s Manual of MGSW-28240F 195 Object Description VLAN ID of the group.  VLAN ID Group address of the group displayed.  Groups Ports under t

User’s Manual of MGSW-28240F 4.8.13 MLDv2 Information Entries in the MLD SFM Information Table are shown on this page. The MLD SFM (Souce-Filtered Mu

User’s Manual of MGSW-28240F 197 4.8.14 MVR The MVR feature enables multicast traffic forwarding on the Multicast VLANs. In a multicast television

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  MVR Mode Enable/Disable the Global MVR. The Unregistered

User’s Manual of MGSW-28240F ports.  Receiver: Configure a port as a receiver port if it is a subscriber port and should only receive multicast dat

User’s Manual of MGSW-28240F Trademarks Copyright © PLANET Technology Corp. 2014. Contents are subject to revision without prior notice. PLANET is

User’s Manual of MGSW-28240F SMTP Test...

User’s Manual of MGSW-28240F The number of Received IGMPv2 Joins and MLDv1 Reports, respectively.  IGMPv2/MLDv1 Reports Received The number of Rece

User’s Manual of MGSW-28240F Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Click to r

User’s Manual of MGSW-28240F 202 : Click to refresh the page immediately. : Updates the table starting from the first entry in the MVR SFM Informat

User’s Manual of MGSW-28240F 4.9 Quality of Service 4.9.1 Understand QOS Quality of Service (QoS) is an advanced traffic prioritization feature t

User’s Manual of MGSW-28240F 4.9.2 Port Policing This page allows you to configure the Policer settings for all switch ports. The Port Policing scree

User’s Manual of MGSW-28240F The page includes the following fields: Object Description The port number for which the configuration below applies. 

User’s Manual of MGSW-28240F Figure 4-9-2: QoS Egress Port Shapers Page Screenshot The page includes the following fields: Object Description  P

User’s Manual of MGSW-28240F Figure 4-9-3: QoS Egress Port Schedule and Shapers Page Screenshot The page includes the following fields: Object Des

User’s Manual of MGSW-28240F Controls the rate for the port shaper. The default value is 500. This value is restricted to 100-1000000 when the "

User’s Manual of MGSW-28240F Figure 4-9-4 : QoS Ingress Port Classification Page Screenshot The page includes the following fields: Object Descrip

User’s Manual of MGSW-28240F Show UPnP ...

User’s Manual of MGSW-28240F Controls the default QoS class, i.e., the QoS class for frames not classified in any other way. There is a one to one ma

User’s Manual of MGSW-28240F Figure 4-9-5 : QoS Ingress Port Tag Classification Page Screenshot The page includes the following fields: Object Des

User’s Manual of MGSW-28240F 4.9.5 Port Scheduler This page provides an overview of QoS Egress Port Schedulers for all switch ports. The Port Schedul

User’s Manual of MGSW-28240F Shows the weight for this queue and port.  Q0 ~ Q5 4.9.6 Port Tag Remarking This page provides an overview of QoS Eg

User’s Manual of MGSW-28240F  Default: Use default PCP/DEI values.  Mapped: Use mapped versions of QoS class and DP level. 4.9.6.1 QoS Egress

User’s Manual of MGSW-28240F 4.9.7 Port DSCP This page allows you to configure the basic QoS Port DSCP Configuration settings for all switch ports.

User’s Manual of MGSW-28240F 216 The page includes the following fields: Object Description The Port coulmn shows the list of ports for which you

User’s Manual of MGSW-28240F 4.9.8 DSCP-Based QoS This page allows you to configure the basic QoS DSCP based QoS Ingress Classification settings for

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Maximum number of support ed DSCP values are 63.  DSCP Cl

User’s Manual of MGSW-28240F Figure 4-9-11: DSCP Translation Page Screenshot 219

User’s Manual of MGSW-28240F 1. INTRODUCTION PLANET MGSW-28240F is a 24-port 100/1000Base-X SFP + 4-port 10G SFP+ L2/L4 Managed Metro Ethernet Swit

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Maximum numbers of supported DSCP values are 64 and valid DS

User’s Manual of MGSW-28240F 4.9.10 DSCP Classification This page allows you to map DSCP value to a QoS Class and DPL value. The DSCP Classification

User’s Manual of MGSW-28240F 4.9.11 QoS Control List This page shows the QoS Control List (QCL), which is made up of the QCEs. Each row describes a

User’s Manual of MGSW-28240F Drop Eligible Indicator: Valid value of DEI can be any of values between 0, 1 or 'Any'.  DEI  Action Indic

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Check the checkbox button in case you what to make any port

User’s Manual of MGSW-28240F DSCP Diffserv Code Point value(DSCP): It can be specific value, range of value or 'Any'. DSCP values are in th

User’s Manual of MGSW-28240F Figure 4-9-15: QoS Control List Status Page Screenshot The page includes the following fields: Object Description Ind

User’s Manual of MGSW-28240F Buttons : Select the QCL status from this drop down list. Auto-refresh : Check this box to refresh the page automaticall

User’s Manual of MGSW-28240F 4.9.13 Storm Control Configuration Storm control for the switch is configured on this page. There is a unicast storm

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  Frame Type The settings in a particular row apply to the

User’s Manual of MGSW-28240F 1.2 Product Descriptions Multiple SFP Fiber Port Switch for Increasing Long-reach Networking of Enterprise, Telecoms

User’s Manual of MGSW-28240F This page allows you to configure the Random Early Detection (RED) settings for queue 0 to 5. RED cannot be applied to q

User’s Manual of MGSW-28240F 4.9.15 QoS Statistics This page provides statistics for the different queues for all switch ports. The QoS Statistics

User’s Manual of MGSW-28240F Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Cli

User’s Manual of MGSW-28240F 4.9.16 Voice VLAN Configuration The Voice VLAN feature enables voice traffic forwarding on the Voice VLAN, then the sw

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  Mode Indicates the Voice VLAN mode operation. We must di

User’s Manual of MGSW-28240F  All means all ports will have one specific setting. Buttons : Click to save changes. : Click to undo any changes made

User’s Manual of MGSW-28240F Buttons : Click to add a new access management entry. : Click to save changes. : Click to undo any changes made locally

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Indicates the ACL user.  User  Ingress Port Indicates th

User’s Manual of MGSW-28240F Buttons : Select the ACL status from this drop down list. Auto-refresh : Check this box to refresh the page automaticall

User’s Manual of MGSW-28240F 239  IPv4/Other: The ACE will match IPv4 frames, which are not ICMP/UDP/TCP.  IPv6: The ACE will match all IPv6 s

User’s Manual of MGSW-28240F Digital Input and Digital Output for External Alarm PLANET MGSW-28240F supports Digital Input, and Digital Output on the

User’s Manual of MGSW-28240F 4.10.3 ACE Configuration Configure an ACE (Access Control Entry) on this page. An ACE consists of several parameters. Th

User’s Manual of MGSW-28240F The allowed range is 0 to 255.  Policy Bitmask When "Specific" is selected for the policy filter, you can en

User’s Manual of MGSW-28240F  MAC Parameters Object Description  SMAC Filter (Only displayed when the frame type is Ethernet Type or ARP.) Speci

User’s Manual of MGSW-28240F priority. The allowed number range is 0 to 7. The value Any means that no tag priority is specified (tag priority is &qu

User’s Manual of MGSW-28240F  ARP SMAC Match Specify whether frames can hit the action according to their sender hardware address field (SHA) setti

User’s Manual of MGSW-28240F defining UDP parameters will apper. These fields are explained later in this help file.  TCP: Select TCP to filter I

User’s Manual of MGSW-28240F  DIP Filter Specify the destination IP filter for this ACE.  Any: No destination IP filter is specified. (Destinat

User’s Manual of MGSW-28240F  Specific: If you want to filter a specific TCP/UDP source filter with this ACE, you can enter a specific TCP/UDP sour

User’s Manual of MGSW-28240F  TCP RST Specify the TCP "Reset the connection" (RST) value for this ACE.  0: TCP frames where the RST f

User’s Manual of MGSW-28240F Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. : Retur

User’s Manual of MGSW-28240F AC and DC Redundant Power to Ensure Continuous Operation PLANET MGSW-28240F is equipped with one 100~240V AC power sup

User’s Manual of MGSW-28240F Figure 4-10-4: ACL Ports Configuration Page Screenshot The page includes the following fields: Object Description The

User’s Manual of MGSW-28240F value is "Permit". All means all ports will have one specific setting. Select which rate limiter to apply to t

User’s Manual of MGSW-28240F : Click to clear the counters. 4.10.5 ACL Rate Limiter Configuration Configure the rate limiter for the ACL of the swi

User’s Manual of MGSW-28240F Buttons : Click to save changes. : Click to undo any changes made locally and revert to previously saved values. 253

User’s Manual of MGSW-28240F 4.11 Authentication This section is to control the access of the Managed Switch, includes the user access and management

User’s Manual of MGSW-28240F 255 is a valid RADIUS user can be used by anyone, and only the MD5-Challenge method is supported. The 802.1X and MAC

User’s Manual of MGSW-28240F  Device Roles With 802.1X port-based authentication, the devices in the network have specific roles as shown below. F

User’s Manual of MGSW-28240F Authentication Protocol (EAP) frames and interacting with the authentication server. When the switch receives EAPOL fram

User’s Manual of MGSW-28240F Figure 4-11-2: EAP Message Exchange  Ports in Authorized and Unauthorized States The switch port state determines wh

User’s Manual of MGSW-28240F 259 4.11.2 Authentication Configuration This page allows you to configure how a user is authenticated when he logs int

User’s Manual of MGSW-28240F 26 1.3 How to Use This Manual This User Manual is structured as follows: Section 2, INSTALLATION The section explains

User’s Manual of MGSW-28240F 4.11.3 Network Access Server Configuration This page allows you to configure the IEEE 802.1X and MAC-based authenticatio

User’s Manual of MGSW-28240F 261 Figure 4-11-4: Network Access Server Configuration Page Screenshot

User’s Manual of MGSW-28240F The page includes the following fields: System Configuration Object Description  Mode Indicates if NAS is globally en

User’s Manual of MGSW-28240F the entry.  Hold Time This setting applies to the following modes, i.e. modes using the Port Security functionality to

User’s Manual of MGSW-28240F timeout. The switch follows a set of rules for entering and leaving the Guest VLAN as listed below. The "Guest VLAN

User’s Manual of MGSW-28240F Force Unauthorized In this mode, the switch will send one EAPOL Failure frame when the port link comes up, and any clien

User’s Manual of MGSW-28240F other clients connected to the port (for instance through a hub) to piggy-back on the successfully authenticated client

User’s Manual of MGSW-28240F limited using the Port Security Limit Control functionality. MAC-based Auth. Unlike port-based 802.1X, MAC-based authe

User’s Manual of MGSW-28240F the RADIUS-assigned). This option is only available for single-client modes, i.e. • Port-based 802.1X • Single 802.1X RA

User’s Manual of MGSW-28240F attributes must all be present at least once in the Access-Accept packet.- The switch looks for the first set of these

User’s Manual of MGSW-28240F 1.4 Product Features  Physical Port  24 100/1000Base-X SFP mini-GBIC slots  4 1/10GBase-SR/LR SFP mini-GBIC slots

User’s Manual of MGSW-28240F While in the Guest VLAN, the switch monitors the link for EAPOL frames, and if one such frame is received, the switch im

User’s Manual of MGSW-28240F 4.11.4 Network Access Overview This page provides an overview of the current NAS port states for the selected switch. Th

User’s Manual of MGSW-28240F EAPOL-based authentication, and the most recently received frame from a new client for MAC-based authentication.  Last

User’s Manual of MGSW-28240F The page includes the following fields: Port State Object Description  Admin State The port's current administra

User’s Manual of MGSW-28240F Response Identity frames) that have been received by the switch. Rx dot1xAuthEapolStartFramesRx Start The number of EAP

User’s Manual of MGSW-28240F  Single 802.1X  Multi 802.1X  MAC-based Auth. Direction IEEE Name Name Description Rx Access Challengesdot1xAu

User’s Manual of MGSW-28240F that the switch receives a failure message. This indicates that the supplicant/client has not authenticated to the backe

User’s Manual of MGSW-28240F dot1xAuthLastEapolFrameVersion Version 802.1X-based: The protocol version number carried in the most recently received

User’s Manual of MGSW-28240F through the Port Security module.  State The client can either be authenticated or unauthenticated. In the authenticat

User’s Manual of MGSW-28240F 279 4.11.6 Authentication Server Configuration This page allows you to configure the Authentication Servers. The Authe

User’s Manual of MGSW-28240F  STP, IEEE 802.1D Spanning Tree Protocol  RSTP, IEEE 802.1w Rapid Spanning Tree Protocol  MSTP, IEEE 802.1s Multip

User’s Manual of MGSW-28240F The page includes the following fields: Port State These setting are common for all of the Authentication Servers. Objec

User’s Manual of MGSW-28240F RADIUS Accounting Server Configuration The table has one row for each RADIUS Accounting Server and a number of columns,

User’s Manual of MGSW-28240F 4.11.7 RADIUS Overview This page provides an overview of the status of the RADIUS servers configurable on the Authentica

User’s Manual of MGSW-28240F 283 expires. The number of seconds left before this occurs is displayed in parentheses. This state is only reachable w

User’s Manual of MGSW-28240F 4.11.8 RADIUS Details This page provides detailed statistics for a particular RADIUS server. The RADIUS Authentication/A

User’s Manual of MGSW-28240F or invalid) received from the server. Rx Access RejectsradiusAuthClientExtAccessRejects The number of RADIUS Access-Reje

User’s Manual of MGSW-28240F reason. Tx radiusAuthClientExtAccessRequests Access Requests The number of RADIUS Access-Request packets sent to the se

User’s Manual of MGSW-28240F State - Shows the state of the server. It takes one of the following values: Disabled: The selected server is disabled

User’s Manual of MGSW-28240F an invalid length. Bad authenticators or or unknown types are not included as malformed access responses.Rx Bad Authenti

User’s Manual of MGSW-28240F the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well a

User’s Manual of MGSW-28240F  DHCP Snooping to Filter Untrusted DHCP Messages  Dynamic ARP Inspection discards ARP Packets with Invalid MAC Addre

User’s Manual of MGSW-28240F 290 Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds.

User’s Manual of MGSW-28240F 2. Add New RADIUS Cleint on the Windows 2003 server Figure 4-11-11: Windows Server – Add New RADIUS Client Setting 3.

User’s Manual of MGSW-28240F 4. The shared secret key should be as same as the key configured on the Managed Switch. Figure 4-11-13: Windows Server

User’s Manual of MGSW-28240F Figure 4-11-15: Windows 2003 AD Server Setting Path 293

User’s Manual of MGSW-28240F 7. Enter ” Active Directory Users and Computers”, create legal user data, the next, right-click a user what you created

User’s Manual of MGSW-28240F 295 Set the Ports Authenticate Status to “Force Authorized” if the port is connected to the RADIUS server or the port

User’s Manual of MGSW-28240F 4. Select “Authentication” tab. 5. Select “Enable network access control using IEEE 802.1X” to enable 802.1x authentic

User’s Manual of MGSW-28240F 9. Enter the user name, password and the logon domain that your account belongs. 10. Click “OK” to complete the valid

User’s Manual of MGSW-28240F 4.12 Security This section is to control the access of the Managed Switch, includes the user access and management contr

User’s Manual of MGSW-28240F 299

User’s Manual of MGSW-28240F TABLE OF CONTENTS 1. INTRODUCTION...

User’s Manual of MGSW-28240F 1.5 Product Specifications Product MGSW-28240F Hardware Specification SFP/mini-GBIC Slots 24 1000Base-SX/LX/BX SFP int

User’s Manual of MGSW-28240F Figure 4-12-1: Port Limit Control Configuration Overview Page Screenshot The page includes the following fields: System

User’s Manual of MGSW-28240F modules may still use the underlying port security features without enabling Limit Control on a given port.  Limit The

User’s Manual of MGSW-28240F 302 Note, that clicking the reopen button causes the page to be refreshed, so non-committed changes will be lost. But

User’s Manual of MGSW-28240F 4.12.2 Access Management Configure access management table on this page. The maximum entry number is 16. If the applicat

User’s Manual of MGSW-28240F 4.12.3 Access Management Statistics This page provides statistics for access management. The Access Management Statistic

User’s Manual of MGSW-28240F 4.12.4 HTTPs Configure HTTPS on this page. The HTTPS Configuration screen in Figure 4-12-4 appears. Figure 4-12-4: HTTP

User’s Manual of MGSW-28240F 4.12.5 SSH Configure SSH on this page. This page shows the Port Security status. Port Security is a module with no direc

User’s Manual of MGSW-28240F 4.12.6 Port Security Status This page shows the Port Security status. Port Security is a module with no direct configura

User’s Manual of MGSW-28240F The page includes the following fields: User Module Legend The legend shows all user modules that may request Port Secur

User’s Manual of MGSW-28240F Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Cl

User’s Manual of MGSW-28240F Up to 256 VLAN groups, out of 4094 VLAN IDs Port Trunking IEEE 802.3ad LACP / Static Trunk 12 groups of 16-Port trunk su

User’s Manual of MGSW-28240F If aging is disabled or a user module has decided to hold the MAC address indefinitely, a dash (-) will be shown. Butto

User’s Manual of MGSW-28240F Figure 4-12-8: DHCP Snooping Configuration Screen Page Screenshot 311

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  Snooping Mode Indicates the DHCP snooping mode operation.

User’s Manual of MGSW-28240F The page includes the following fields: Object Description The number of discover (option 53 with value 1) packets rece

User’s Manual of MGSW-28240F 4.12.10 IP Source Guard Configuration IP Source Guard is a secure feature used to restrict IP traffic on DHCP snooping u

User’s Manual of MGSW-28240F Figure 4-12-10: IP Source Guard Configuration Screen Page Screenshot 315

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  Mode of IP Source Guard Configuration Enable the Global I

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Check to delete the entry. It will be deleted during the nex

User’s Manual of MGSW-28240F Figure 4-12-12: ARP Inspection Configuration Screen Page Screenshot 318

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Enable the Global ARP Inspection or disable the Global ARP I

User’s Manual of MGSW-28240F 32 RFC 791 IP RFC 792 ICMP RFC 2068 HTTP RFC 1112 IGMP version 1 RFC 2236 IGMP version 2 RFC 3376 IGMP version 3 Envir

User’s Manual of MGSW-28240F Buttons : Click to add a new entry. : Click to save changes. : Click to undo any changes made locally and revert to pre

User’s Manual of MGSW-28240F 321 4.13 MAC Address Table Switching of frames is based upon the DMAC address contained in the frame. The Managed Swit

User’s Manual of MGSW-28240F The page includes the following fields: Aging Configuration By default, dynamic entries are removed from the MAC table a

User’s Manual of MGSW-28240F Buttons : Click to add a new entry. : Click to save changes. : Click to undo any changes made locally and revert to prev

User’s Manual of MGSW-28240F The page includes the following fields: Object Description Indicates whether the entry is a static or dynamic entry. 

User’s Manual of MGSW-28240F the value of the first displayed entry, allowing for continuous refresh with the same start address. The “>>” will

User’s Manual of MGSW-28240F starting point in the Dynamic IP Source Guard Table. Clicking the “Refresh” button will update the displayed table start

User’s Manual of MGSW-28240F 4.14 LLDP 4.14.1 Link Layer Discovery Protocol Link Layer Discovery Protocol (LLDP) is used to discover basic informat

User’s Manual of MGSW-28240F 328 Figure 4-14-1: LLDP Configuration Page Screenshot

User’s Manual of MGSW-28240F The page includes the following fields: LLDP Parameters Object Description The switch is periodically transmitting LLDP

User’s Manual of MGSW-28240F 2. INSTALLATION 2.1 Hardware Descriptions The Managed Switch provides four different running speeds – 10Mbps, 100Mbps, 1

User’s Manual of MGSW-28240F from neighbor units is analyzed.  Tx only The switch will drop LLDP information received from neighbors, but will se

User’s Manual of MGSW-28240F by this TLV is described in IEEE 802.1AB.  Management Address Optional TLV: When checked the "management address&

User’s Manual of MGSW-28240F The page includes the following fields: Fast start repeat count Object Description  Fast start repeat count Rapid sta

User’s Manual of MGSW-28240F It is possible to specify the direction to either North of the equator or South of the equator.  Longitude Longitude S

User’s Manual of MGSW-28240F City division, borough, city district, ward, chou (Japan)  City district  Block (Neighborhood) Neighborhood, block S

User’s Manual of MGSW-28240F Policies Network Policy Discovery enables the efficient discovery and diagnosis of mismatch issues with the VLAN configu

User’s Manual of MGSW-28240F different policy for the voice signaling than for the voice media. This application type should not be advertised if all

User’s Manual of MGSW-28240F L2 Priority is the Layer 2 priority to be used for the specified application type. L2 Priority may specify one of eight

User’s Manual of MGSW-28240F 4.14.4 LLDP-MED Neighbor This page provides a status overview for all LLDP-MED neighbors. The displayed table contains

User’s Manual of MGSW-28240F Within the LLDP-MED Endpoint Device category, the LLDP-MED scheme is broken into further Endpoint Device Classes, as def

User’s Manual of MGSW-28240F Reset Button Pressed and Released Function < 5 sec: System Reboot Reboot the Managed Switch > 5 sec: Factory D

User’s Manual of MGSW-28240F communication appliances that directly support the end user. Discovery services defined in this class include provision

User’s Manual of MGSW-28240F Video Signaling - for use in network topologies that require a separate policy for the video signaling than for the vide

User’s Manual of MGSW-28240F 4.14.5 Neighbor This page provides a status overview for all LLDP neighbors. The displayed table contains a row for ea

User’s Manual of MGSW-28240F 4.14.6 Port Statistics This page provides an overview of all LLDP traffic. Two types of counters are shown. Global count

User’s Manual of MGSW-28240F 344 Entries Deleted Shows the number of LLDP frames dropped due to that the entry table was full.  Total Neighbors E

User’s Manual of MGSW-28240F 4.15 Diagnostics This section provide the Physical layer and IP layer network diagnostics tools for troubleshoot. The di

User’s Manual of MGSW-28240F 4.15.1 Ping This page allows you to issue ICMP PING packets to troubleshoot IP connectivity issues. After you press “S

User’s Manual of MGSW-28240F 4.15.2 IPv6 Ping This page allows you to issue ICMPv6 PING packets to troubleshoot IPv6 connectivity issues. After you p

User’s Manual of MGSW-28240F Figure 4-15-3: Remote IP Ping Test Page Screenshot 348

User’s Manual of MGSW-28240F The page includes the following fields: Object Description The logical port for the settings.  Port The destination I

User’s Manual of MGSW-28240F voltage from -36V to -60V DC. Connect the power cable to the Managed Switch at the input terminal block. The size of the

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  Port The port where you are requesting Cable Diagnostics

User’s Manual of MGSW-28240F Figure 4-16-1: Loop Protection Configuration Page Screenshot 351

User’s Manual of MGSW-28240F The page includes the following fields: General Settings: Object Description Controls whether loop protections is enabl

User’s Manual of MGSW-28240F 353 The page includes the following fields: Object Description The switch port number of the logical port.  Port T

User’s Manual of MGSW-28240F 4.17 RMON RMON is the most important expansion of the standard SNMP. RMON is a set of MIB definitions, used to define st

User’s Manual of MGSW-28240F framing characters.  InUcastPkts: The number of uni-cast packets delivered to a higher-layer protocol.  InNUcastPkts

User’s Manual of MGSW-28240F Buttons : Click to add a new community entry. : Click to save changes. : Click to undo any changes made locally and reve

User’s Manual of MGSW-28240F Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Cli

User’s Manual of MGSW-28240F Buttons : Click to add a new community entry. : Click to save changes. : Click to undo any changes made locally and reve

User’s Manual of MGSW-28240F 4.17.5 RMON History Configuration Configure RMON History table on this page. The entry index key is ID; screen in Figure

User’s Manual of MGSW-28240F Lights Indicates the link through that SFP port is successfully established with speed 10Mbps or 100Mbps. Blink Indica

User’s Manual of MGSW-28240F Figure 4-17-6: RMON history overview page screenshot The page includes the following fields: Object Description Indic

User’s Manual of MGSW-28240F Buttons Auto-refresh : Check this box to refresh the page automatically. Automatic refresh occurs every 3 seconds. : Cli

User’s Manual of MGSW-28240F Figure 4-17-8 appears. Figure 4-17-8: RMON Statistics Status page screenshot The page includes the following fields: O

User’s Manual of MGSW-28240F The total number of packets (including bad packets) received that were from 65 to 127 octets in length.  65~127 The to

User’s Manual of MGSW-28240F 4.18 PTP 4.18.1 PTP Configuration PTP is an acronym for Precision Time Protocol, a network protocol for synchronizing th

User’s Manual of MGSW-28240F This will allow setting the Clock Frequency.  Clock Frequency The possible range of values are 1 - 25000000 (1 - 25M

User’s Manual of MGSW-28240F  Clock Instance Indicates the Instance of a particular Clock Instance [0..3]. Click on the Clock Instance number to

User’s Manual of MGSW-28240F 4.19 Ring ITU-T G.8032 Ethernet Ring protection switching (ERPS) is a link layer protocol applied on Ethernet loop prote

User’s Manual of MGSW-28240F 4.19.1 MEP Configuration The Maintenance Entity Point instances are configured here as screen in Figure 4-19-1 is show

User’s Manual of MGSW-28240F Port: This is an MEP in the Port Domain. 'Flow Instance' is a Port. Esp: Future use Evc: This is an MEP in the

User’s Manual of MGSW-28240F 2.1.3 Wiring the AC Power Input The front panel of the MGSW-28240F indicates an AC inlet power socket, which accepts inp

User’s Manual of MGSW-28240F Figure 4-19-2: Detailed MEP configuration page screenshot The page includes the following fields: Instance Data: Objec

User’s Manual of MGSW-28240F  Format This is the configuration of the two possible Maintenance Association Identifier formats. ITU ICC: This is de

User’s Manual of MGSW-28240F Buttons : Click to add a new peer MEP. Functional Configuration Instance Data: Object Description  Enable Continuit

User’s Manual of MGSW-28240F in G.8032. R-APS: APS PDU is transmitted as R-APS - this is for ERPS.  Type L-APS: APS PDU is transmitted as L-APS - t

User’s Manual of MGSW-28240F The Port 1 Signal Fail reporting MEP. As only one SF MEP is associated with interconnected sub-ring without virtual chan

User’s Manual of MGSW-28240F Figure 4-19-4: Ethernet Ring Protocol Switch Configuration page screenshot The page includes the following fields: Ins

User’s Manual of MGSW-28240F R-APS messages. The period of the guard timer can be configured in 10 ms steps between 10 ms and 2 seconds, with a defau

User’s Manual of MGSW-28240F ERPS state according to State Transition Tables in G.8032.  Protection State  Port 0 OK: State of East port is ok SF

User’s Manual of MGSW-28240F 4.19.5 Ring Wizard This page allows the user to configure the ERPS by wizard; screen in Figure 4-19-4 appears. Figure 4

User’s Manual of MGSW-28240F 4.19.6 Ring Wizard Example: Figure 4-19-6: Ring Example Diagram The above topology often occurs on using ERPS protocol.

User’s Manual of MGSW-28240F Figure 2-3: MGSW-28240F Upper Panel 2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 3

User’s Manual of MGSW-28240F Setup steps Set ERPS Configuration on Switch 1 Connect PC to switch 1 directly; don’t connect to port 1 & 2 Log-in o

User’s Manual of MGSW-28240F To avoid loop, please don’t connect switch 1, 2 & 3 together in the ring topology before configuring the end of

User’s Manual of MGSW-28240F 5. COMMAND LINE INTERFACE 5.1 Accessing the CLI When accessing the management interface for the Managed Switch via a T

User’s Manual of MGSW-28240F 383 6. COMMAND LINE MODE The CLI groups all the commands in appropriate modes according to the nature of the command.

User’s Manual of MGSW-28240F 6.1 System Command System Configuration Description: Show system configuration. Syntax: System Configuration [all] [&

User’s Manual of MGSW-28240F Example: To display system log information: MGSW-28240F:/>System log configuration System Log Configuration: =====

User’s Manual of MGSW-28240F System Log Server Mode Description: Show or set the system log server mode. Syntax: System Log Server Mode [enable|dis

User’s Manual of MGSW-28240F System Timezone Offset Description: Set or show the system timezone offset. Syntax: System Timezone Offset [<offset&

User’s Manual of MGSW-28240F Default Setting: empty Example: To set log server address: MGSW-28240F:/> log server address 192.168.0.21 Syste

User’s Manual of MGSW-28240F Parameters: <location>: System location string. (1-255) Use 'clear' or "" to clear

User’s Manual of MGSW-28240F Insert the wires into the faulty alarm contacts 1. The wire gauge for the terminal block should be in the range of 12

User’s Manual of MGSW-28240F Syntax: System DST Mode [disable|recurring|non-recurring] Parameters: disable: Disable Daylight Saving Time recurring :

User’s Manual of MGSW-28240F all : Show all levels (default) info : Show informations warning : Show warnings error : Show errors System

User’s Manual of MGSW-28240F System Reboot Description: Reboot the system. Syntax: System Reboot Example: To reboot device without changing any of

User’s Manual of MGSW-28240F System Load Description: Show current CPU load: 100ms, 1s and 10s running average (in percent, zero is idle). Syntax: S

User’s Manual of MGSW-28240F 6.2 IP Command IP Configuration Description: Show IP configuration. Syntax: IP Configuration Example: Show IP confi

User’s Manual of MGSW-28240F Parameters: enable : Enable or renew DHCP client disable: Disable DHCP client Default Setting: Disable Example: Disab

User’s Manual of MGSW-28240F IP Ping Description: Ping IP address (ICMP echo). Syntax: IP Ping <ip_addr_string> [(Length <ping_length>)]

User’s Manual of MGSW-28240F IP DNS Proxy Description: Set or show the IP DNS Proxy mode. Syntax: IP DNS_Proxy [enable|disable] Parameters: enable

User’s Manual of MGSW-28240F IPv6 Setup Description: Set or show the IPv6 setup. Syntax: IP IPv6 Setup [<ipv6_addr>] [<ipv6_prefix>] [&l

User’s Manual of MGSW-28240F Parameters: <ipv6_addr>: IPv6 address is in 128-bit records represented as eight fields of up to four hexadecimal

User’s Manual of MGSW-28240F 4.2 System...

User’s Manual of MGSW-28240F 2. Tighten the wire-clamp screws for preventing the wires from loosening. 1 2 3 4 5 6 DI0 DI1 DO0 DO1 GND GNDFigure 2-

User’s Manual of MGSW-28240F IP NTP Configuration Default Setting: IP NTP Configuration: ===================== NTP Mode : Disabled Idx Server

User’s Manual of MGSW-28240F IP NTP Server Add Description: Add NTP server entry. Syntax: IP NTP Server Add <server_index> <ip_addr_string&

User’s Manual of MGSW-28240F IP NTP Server Delete Description: Delete NTP server entry. Syntax: IP NTP Server Delete <server_index> Parameter

User’s Manual of MGSW-28240F 6.3 Port Management Command Port Configuration Description: Show port configuration. Syntax: Port Configuration [<

User’s Manual of MGSW-28240F Parameters: <port_list>: Port list or 'all', default: All ports auto : Auto negotiation of speed a

User’s Manual of MGSW-28240F Port State Description: Set or show the port administrative state. Syntax: Port State [<port_list>] [enable|disab

User’s Manual of MGSW-28240F Port Power Description: Set or show the port PHY power mode. Syntax: Port Power [<port_list>] [enable|disable|act

User’s Manual of MGSW-28240F Example: MGSW-28240F:/>port excessive 1 restart Port Statistics Description: Show port statistics. Syntax: Port S

User’s Manual of MGSW-28240F Port SFP Description: Show SFP port information. Syntax: Port SFP [<port_list>] Parameters: <port_list>: P

User’s Manual of MGSW-28240F 6.4 MAC Address Table Command MAC Configuration Description: Show MAC address table configuration. Syntax: MAC Configur

User’s Manual of MGSW-28240F 4. There are two Digital Output groups for you to sense MGSW-28240F port failure or power failure and issue a high or l

User’s Manual of MGSW-28240F Add MAC address table entry. Syntax: MAC Add <mac_addr> <port_list> [<vid>] Parameters: <mac_addr&

User’s Manual of MGSW-28240F Parameters: <mac_addr>: MAC address (xx-xx-xx-xx-xx-xx) <vid> : VLAN ID (1-4095), default: 1 Example:

User’s Manual of MGSW-28240F auto : Automatic learning disable: Disable learning secure : Secure learning (default: Show learn mode) Default Setti

User’s Manual of MGSW-28240F 413 MAC Statistics Description: Show MAC address table statistics. Syntax: MAC Statistics [<port_list>] Parame

User’s Manual of MGSW-28240F 6.5 VLAN Configuration Command VLAN Configuration Description: Show VLAN configuration. Syntax: VLAN Configuration [<

User’s Manual of MGSW-28240F VLAV PVID Description: Set or show the port VLAN ID. Syntax: VLAN PVID [<port_list>] [<vid>|none] Parameter

User’s Manual of MGSW-28240F MGSW-28240F:/>vlan frametype 10 tagged VLAN Ingress Filter Description: Set or show the port VLAN ingress filter.

User’s Manual of MGSW-28240F 417 IEEE 802.1Q Example: Set VLAN mode in port base MGSW-28240F:/>vlan mode portbased VLAN Link Type Descript

User’s Manual of MGSW-28240F Parameters: <port_list>: Port list or 'all', default: All ports disable : Disable Q-in-Q VLAN Mode m

User’s Manual of MGSW-28240F Syntax: VLAN untagVID [<port_list>] [<untagvid>] Parameters: <port_list>: Port list or 'all&apos

User’s Manual of MGSW-28240F 2.2 Installing the Managed Switch This section describes how to install your Managed Switch and make connections to the

User’s Manual of MGSW-28240F Parameters: <vid>|<name>: VLAN ID (1-4095) or VLAN Name <port_list> : Port list or 'all', de

User’s Manual of MGSW-28240F VLAN Forbidden Lookup Description: Lookup VLAN Forbidden port entry. Syntax: VLAN Forbidden Lookup [<vid>] [(name

User’s Manual of MGSW-28240F VID VLAN Name Ports ---- -------------------------------- ----- 1 default

User’s Manual of MGSW-28240F VLAN Name Lookup Description: Show VLAN Name table. Syntax: VLAN Name Lookup [<name>] Parameters: <name>:

User’s Manual of MGSW-28240F Promiscous Example: Show VLAN configuration of port10 MGSW-28240F:/>status 1 Port VLAN User PortType P

User’s Manual of MGSW-28240F 6.6 Private VLAN Configuration Command PVLAN Configuration Description: Show Private VLAN configuration. Syntax: PVLAN

User’s Manual of MGSW-28240F PVLAN Add Description: Add or modify Private VLAN entry. Syntax: PVLAN Add <pvlan_id> [<port_list>] Parame

User’s Manual of MGSW-28240F PVLAN Lookup [<pvlan_id>] Parameters: <pvlan_id>: Private VLAN ID, default: Show all PVLANs. The allowed ra

User’s Manual of MGSW-28240F 6.7 Security Command Security Switch User Configuration Description: Show users configuration. Syntax: Security Switch

User’s Manual of MGSW-28240F Example: Add new user: username: test, password: test & privilege: 10 MGSW-28240F:/>security switch users add

User’s Manual of MGSW-28240F When the Managed Switch receives power, the Power LED should remain solid Green. 2.2.2 Rack Mounting To install the Man

User’s Manual of MGSW-28240F Parameters: <group_name>: Privilege group name <cro> : Configuration read-only privilege level (1-15)

User’s Manual of MGSW-28240F Client Authentication Method Local Authentication Fallback ------- ---------------------- --------------

User’s Manual of MGSW-28240F Security Switch SSH Configuration Description: Show SSH configuration. Syntax: Security Switch SSH Configuration Examp

User’s Manual of MGSW-28240F Security Switch HTTPs Configuration Description: Show HTTPS configuration. Syntax: Security Switch HTTPS Configuration

User’s Manual of MGSW-28240F Security Switch HTTPs Redirect Description: Set or show the HTTPS redirect mode. Automatic redirect web browser to HTTPS

User’s Manual of MGSW-28240F Security Switch Access Mode Description: Set or show the access management mode. Syntax: Security Switch Access Mode [e

User’s Manual of MGSW-28240F MGSW-28240F:/>security switch access add 1 192.168.0.1 192.168.0.200 web Security Switch Access IPv6 Add Descriptio

User’s Manual of MGSW-28240F Syntax: Security Switch Access Delete <access_id> Parameters: <access_id>: entry index (1-16) Example:

User’s Manual of MGSW-28240F Security Switch Access Statistics Description: Show or clear access management statistics. Syntax: Security Switch Acce

User’s Manual of MGSW-28240F Parameters: enable : Enable SNMP disable: Disable SNMP (default: Show SNMP mode) Default Setting: enable Example: D

User’s Manual of MGSW-28240F Figure 2-6 Mounting the Managed Switch on a Rack Step6: Proceeds with steps 4 and 5 of session 2.2.1 Desktop Installati

User’s Manual of MGSW-28240F Syntax: Security Switch SNMP Read Community [<community>] Parameters: <community>: Community string. Use &a

User’s Manual of MGSW-28240F Syntax: Security Switch SNMP Trap Mode [enable|disable] Parameters: enable : Enable SNMP traps disable: Disable SNMP tr

User’s Manual of MGSW-28240F Security Switch SNMP Trap Community Description: Set or show the community string for SNMP traps. Syntax: Security Swit

User’s Manual of MGSW-28240F Set or Show the SNMP trap destination IPv6 address. Syntax: Security Switch SNMP Trap IPv6 Destination [<ipv6_addr&g

User’s Manual of MGSW-28240F Security Switch SNMP Trap Link-up Description: Set or show the port link-up and link-down trap mode. Syntax: Security S

User’s Manual of MGSW-28240F Security Switch SNMP Trap Inform Timeout Description: Set or show the SNMP trap inform timeout (usecs). Syntax: Securit

User’s Manual of MGSW-28240F Security Switch SNMP Trap Probe Security Engine ID Description: Show SNMP trap security engine ID probe mode. Syntax: S

User’s Manual of MGSW-28240F Security Switch SNMP Trap Security Name Description: Set or show SNMP trap security name. Syntax: Security Switch SNMP

User’s Manual of MGSW-28240F Add or modify SNMPv3 community entry. The entry index key is <community>. Syntax: Security Switch SNMP Community

User’s Manual of MGSW-28240F Parameters: <index>: entry index (1-64) Example: Lookup SNMPv3 community entry MGSW-28240F:/>security switch

User’s Manual of MGSW-28240F 45 2.3 Cabling  10/100/1000Base-T and 100Base-FX / 1000Base-SX/LX All 10/100/1000Base-T ports come with Auto-Negotia

User’s Manual of MGSW-28240F MGSW-28240F:/>security switch snmp user add 800007e5017f000003 admin_snmpv3 md5 12345678 des abcdefgh Security Swit

User’s Manual of MGSW-28240F 87654321 12345678 Security Switch SNMP User Lookup Description: Lookup SNMPv3 user entry. Syntax: Security Switch SNM

User’s Manual of MGSW-28240F (1-32), and the allowed content is ASCII characters from 33 to 126 Example: Add SNMPv3 group entry MGSW-28240F:/>se

User’s Manual of MGSW-28240F 1 v1 public default_ro_group 2 v1 private default_rw_group

User’s Manual of MGSW-28240F <index>: entry index (1-64) Example: Delete SNMPv3 view entry MGSW-28240F:/>security switch snmp view delete

User’s Manual of MGSW-28240F Parameters: <group_name> : A string identifying the group name that this entry should belong to. The allo

User’s Manual of MGSW-28240F Security Switch SNMP Access Lookup Description: Lookup SNMPv3 access entry. Syntax: Security Switch SNMP Access Lookup

User’s Manual of MGSW-28240F Syntax: Security Switch RMON Statistics Delete <stats_id> Parameters: <stats_id>: Statistics ID (1-65535).

User’s Manual of MGSW-28240F Syntax: Security Switch RMON History Delete <history_id> Parameters: <history_id> : History ID (1-65535).

User’s Manual of MGSW-28240F 459 .1.3.6.1.2.1.2.2.1.18.xxx – ifOutNUcastPkts .1.3.6.1.2.1.2.2.1.19.xxx – ifOutDiscards .1.3.6.1.2.1.2.2.1.20.xxx –

User’s Manual of MGSW-28240F 2.3.1 Installing the SFP Transceiver The sections describe how to insert an SFP transceiver into an SFP slot. The SFP

User’s Manual of MGSW-28240F Security Switch RMON Event Add Description: Add or modify RMON Event entry. The entry index key is <event_id>. Sy

User’s Manual of MGSW-28240F Security Network Psec Switch Description: Show Port Security status. Syntax: Security Network Psec Switch [<port_lis

User’s Manual of MGSW-28240F Security Network Psec Port [<port_list>] Parameters: <port_list>: Port list or 'all', default: Al

User’s Manual of MGSW-28240F Port Mode Limit Action ---- -------- ----- --------------- 1 Disabled 4 None 2 Disabled

User’s Manual of MGSW-28240F Syntax: Security Network Limit Aging [enable|disable] Parameters: enable : Enable aging disable : Disable aging (defau

User’s Manual of MGSW-28240F Security Network Limit Port [<port_list>] [enable|disable] Parameters: <port_list>: Port list or 'all&

User’s Manual of MGSW-28240F Security Network Limit Action Description: Set or show the action involved with exceeding the limit. Syntax: Security N

User’s Manual of MGSW-28240F Security Network NAS Configuration Description: Show 802.1X configuration. Syntax: Security Network NAS Configuration [

User’s Manual of MGSW-28240F Syntax: Security Network NAS Mode [enable|disable] Parameters: enable : Globally enable 802.1X disable: Globally disabl

User’s Manual of MGSW-28240F MGSW-28240F:/>security network nas state 1 Port Admin State Port State Last Source Last

User’s Manual of MGSW-28240F MGB-LA40 SFP-Port 1000Base-LX (WDM,TX:1310nm) mini-GBIC module - 40KM MGB-LB40 SFP-Port 1000Base-LX (WDM,TX:1550nm) mi

User’s Manual of MGSW-28240F (default: Show current per-port RADIUS-assigned VLAN enabledness) enable : Enable RADIUS-assigned VLAN either globally o

User’s Manual of MGSW-28240F Security Network NAS Agetime [<age_time>] Parameters: <age_time>: Time between checks for activitiy on a MA

User’s Manual of MGSW-28240F Security Network NAS RADIUS_QoS [global|<port_list>] [enable|disable] Parameters: global : Select the global

User’s Manual of MGSW-28240F MGSW-28240F:/>security network nas radius_vlan enable Security Network NAS Guest_VLAN Description: Set or show eith

User’s Manual of MGSW-28240F Security Network NAS Authenticate Description: Refresh (restart) 802.1X authentication process. Syntax: Security Networ

User’s Manual of MGSW-28240F Rx Response: 0 Tx Request: 0 Rx Start: 0 R

User’s Manual of MGSW-28240F <logging> : System logging of frames: log|log_disable <shutdown> : Shut down ingress port: shut|shut_

User’s Manual of MGSW-28240F Parameters: <rate_limiter_list>: Rate limiter list (1-16), default: All rate limiters <rate_unit> : I

User’s Manual of MGSW-28240F <tagged> : Tagged of frames: any|enable|disable <vid> : VLAN ID (1-4095) or 'any' <

User’s Manual of MGSW-28240F Security Network ACL Delete <ace_id> Parameters: <ace_id>: ACE ID (1-256) Example: Delete ACE 1 MGSW-282

User’s Manual of MGSW-28240F 100Base-FX: Before connecting the other switches, workstation or media converter. 1. Make sure both sides of the SFP tr

User’s Manual of MGSW-28240F Security Network ACL Status Description: Show ACL status. Syntax: Security Network ACL Status [combined|static|dhcp|upn

User’s Manual of MGSW-28240F Security Network DHCP Relay Configuration Description: Show DHCP relay configuration. Syntax: Security Network DHCP Rela

User’s Manual of MGSW-28240F Enable DHCP relay mode MGSW-28240F:/>security network dhcp relay mode enable Security Network DHCP Relay Server D

User’s Manual of MGSW-28240F disable Example: Enable DHCP relay agent information option mode. MGSW-28240F:/>security network dhcp relay infor

User’s Manual of MGSW-28240F Parameters: clear: Clear DHCP relay statistics Example: Show DHCP relay statistics. MGSW-28240F:/>security networ

User’s Manual of MGSW-28240F Security Network DHCP Snooping Port Mode Description: Set or show the DHCP snooping port mode. Syntax: Security Network

User’s Manual of MGSW-28240F Rx Discover: 0 Tx Discover: 0 Rx Offer: 0

User’s Manual of MGSW-28240F MGSW-28240F:/>security network ip source guard mode enable Security Network IP Source Guard Port Mode Description:

User’s Manual of MGSW-28240F Example: Set IP source guard limit MGSW-28240F:/>security network ip source guard 1 1 Security Network IP Sourc

User’s Manual of MGSW-28240F Show IP source guard static and dynamic entries. MGSW-28240F:/>security network ip source guard status Security N

User’s Manual of MGSW-28240F 49 Never pull out the module without lifting up the lever of the module and turning it to a horizontal position. Dire

User’s Manual of MGSW-28240F Example: Enable ARP inspection mode MGSW-28240F:/>security network arp inspection mode enable Security Network

User’s Manual of MGSW-28240F delete : Delete existing port ARP inspection static entry <vid> : VLAN ID (1-4095) <allowed_mac>: MAC

User’s Manual of MGSW-28240F Show Auth configuration. Syntax: Security AAA Configuration Example: Show Auth configuration. MGSW-28240F:/>securi

User’s Manual of MGSW-28240F ------ -------- --------------- ------------------------------ ----- 1 Disabled

User’s Manual of MGSW-28240F Default Setting: 300 Example: Set 1000sec for server dead time MGSW-28240F:/>security aaa deadtime 1000 Securi

User’s Manual of MGSW-28240F Syntax: Security AAA ACCT_RADIUS [<server_index>] [enable|disable] [<ip_addr_string>] [<secret>] [<

User’s Manual of MGSW-28240F <server_port> : Server TCP port. Use 0 to use the default TACACS+ port (49) Example: Set TACACS+ authenticati

User’s Manual of MGSW-28240F 6.8 Spanning Tree Protocol Command STP Configuration Description: Show STP configuration. Syntax: STP Configuration Ex

User’s Manual of MGSW-28240F Example: Set the STP Bridge protocol version. MGSW-28240F:/> stp version rstp STP Tx Hold Description: Set or sh

User’s Manual of MGSW-28240F Set STP maximum hops in 25 MGSW-28240F:/>stp maxhops 25 STP MaxAge Description: Set or show the bridge instance m

User’s Manual of MGSW-28240F 4.4.3 Detailed Port Statistics...

User’s Manual of MGSW-28240F 3. SWITCH MANAGEMENT This chapter explains the methods that you can use to configure management access to the Managed Sw

User’s Manual of MGSW-28240F MGSW-28240F:/>stp fwddelay 25 STP CName Description: Set or Show MSTP configuration name and revision. Syntax: STP

User’s Manual of MGSW-28240F Example: Set edge port BPDU filtering MGSW-28240F:/>stp bpdufilter enable STP BPDU Guard Description: Set or sho

User’s Manual of MGSW-28240F Example: Set STP recovery value in 30 sec. MGSW-28240F:/>stp recovery 30 STP Status Description: Show STP Bridge

User’s Manual of MGSW-28240F STP MSTI Priority Description: Set or show the bridge instance priority. Syntax: STP Msti Priority [<msti>] [<

User’s Manual of MGSW-28240F STP MSTI Add Description: Add a VLAN to a MSTI. Syntax: STP Msti Add <msti> <vid> Parameters: <msti>

User’s Manual of MGSW-28240F STP Port Mode Description: Set or show the STP enabling for a port. Syntax: STP Port Mode [<port_list>] [enable|d

User’s Manual of MGSW-28240F MGSW-28240F:/>stp port edge 1 enable STP Port AutoEdge Description: Set or show the STP autoEdge port parameter. S

User’s Manual of MGSW-28240F 507 Default: auto Example: Disable STP P2P function on port1 MGSW-28240F:/>stp port p2p 1 disable STP Port Re

User’s Manual of MGSW-28240F Parameters: <port_list>: Port list or 'all', default: All ports enable : Enable MSTP restricted TCN d

User’s Manual of MGSW-28240F Syntax: STP Port Statistics [<port_list>] [clear] Parameters: <port_list>: Port list or 'all', def

User’s Manual of MGSW-28240F 51 3.2 Management Access Overview The Managed Switch gives you the flexibility to access and manage it using any or al

User’s Manual of MGSW-28240F <port_list>: Port list or 'all', default: All ports Default: auto STP MSTI Port Cost Description: Set

User’s Manual of MGSW-28240F <port_list>: Port list or 'all'. Port zero means aggregations. <priority> : STP port priority (0/1

User’s Manual of MGSW-28240F 6.9 Link Aggregation Command Aggregation Configuration Description: Show link aggregation configuration. Syntax: Aggr C

User’s Manual of MGSW-28240F Example: Delete Group2 MGSW-28240F:/>aggr delete 2 Aggregation Lookup Description: Lookup link aggregation. Synt

User’s Manual of MGSW-28240F Example: Disable SMAC mode MGSW-28240F:/>Aggr mode smac disable 514

User’s Manual of MGSW-28240F 6.10 Link Aggregation Control Protocol Command LACP Configuration Description: Show LACP configuration. Syntax: LACP Co

User’s Manual of MGSW-28240F <port_list>: Port list or 'all', default: All ports enable : Enable LACP protocol disable: Disable LACP

User’s Manual of MGSW-28240F LACP Prio [<port_list>] [<prio>] Parameters: <port_list>: Port list or 'all', default: All

User’s Manual of MGSW-28240F active Example: Set passive for port1~4 MGSW-28240F:/>lacp role 1-4 passive LACP Status Description: Show LACP

User’s Manual of MGSW-28240F Parameters: <port_list>: Port list or 'all', default: All ports clear : Clear LACP statistics Exam

User’s Manual of MGSW-28240F 3.3 CLI Mode Management There are two ways for CLI mode management, one is remote telnet, and the other is operating fro

User’s Manual of MGSW-28240F 6.11 LLDP Command LLDP Configuration Description: Show LLDP configuration. Syntax: LLDP Configuration [<port_list>

User’s Manual of MGSW-28240F Parameters: <port_list>: Port list or 'all', default: All ports enable : Enable LLDP reception and trans

User’s Manual of MGSW-28240F System capabilities: Enable Master's IP address: Enable Example: Disable description of the port for

User’s Manual of MGSW-28240F Example: Set LLDP hold value in 10 MGSW-28240F:/>lldp hold 10 LLDP Delay Description: Set or show LLDP Tx delay.

User’s Manual of MGSW-28240F Example: Set LLDP reinit delay value in 3 MGSW-28240F:/>lldp reinit 3 LLDP Statistics Description: Show LLDP Sta

User’s Manual of MGSW-28240F Syntax: LLDP Info [<port_list>] Parameters: <port_list>: Port list or 'all', default: All ports

User’s Manual of MGSW-28240F 6.12 LLDP MED Command LLDP MED Configuration Description: Show LLDP-MED configuration. Syntax: LLDPMED Configuration [&

User’s Manual of MGSW-28240F Syntax: LLDPMED Civic [country|state|county|city|district|block|street|leading_street_direction|trailing_street_suffix|s

User’s Manual of MGSW-28240F Syntax: LLDPMED ecs [<ecs_value>] Parameters: <ecs_value>: lldpmed The value for the Emergency Call Service

User’s Manual of MGSW-28240F visitors with their own IP Telephony handsets and other similar appliances supporting interactive voice services. guest_

User’s Manual of MGSW-28240F 53 Figure 3-2: Remote Telnet Interface Main Screen of Managed Switch For more information about using the Remote Tel

User’s Manual of MGSW-28240F Set or show LLDP-MED Location. Syntax: LLDPMED Coordinates [latitude|longitude|altitude] [north|south|west|east|meters|

User’s Manual of MGSW-28240F 531 LLDP MED Fast Description: Set or show LLDP-MED Fast Start Repeat Count. Syntax: LLDPMED Fast [<count>] Pa

User’s Manual of MGSW-28240F 6.13 Quality of Service Command QoS Configuration Description: Show QoS Configuration. Syntax: QoS Configuration [<p

User’s Manual of MGSW-28240F QoS Port Classification DPL Description: Set or show the default Drop Precedence Level. Syntax: QoS Port Classification

User’s Manual of MGSW-28240F QoS Port Classification DEI Description: Set or show the default DEI for an untagged frame. Syntax: QoS Port Classifica

User’s Manual of MGSW-28240F MGSW-28240F:/>qos Port Classification tag 1-10 enable QoS Port Classification Map Description: Set or show the port

User’s Manual of MGSW-28240F MGSW-28240F:/>qos Port Classification dscp 1-10 enable QoS Port Policer Mode Description: Set or show the port poli

User’s Manual of MGSW-28240F Example: Set the port policer rate in 1000 MGSW-28240F:/>qos Port Policer Rate 1-10 1000 QoS Port Policer Unit D

User’s Manual of MGSW-28240F enable : Enable port policer flow control disable : Disable port policer flow control (default: Show port policer

User’s Manual of MGSW-28240F Default Setting: 500 QoS Port Scheduler Mode Description: Set or show the port scheduler mode. Syntax: QoS Port Sched

User’s Manual of MGSW-28240F 3.4 Web Management The Managed Switch offers management features that allow users to manage the Managed Switch from anyw

User’s Manual of MGSW-28240F QoS Port QueueShaper Mode Description: Set or show the port queue shaper mode. Syntax: QoS Port QueueShaper Mode [<p

User’s Manual of MGSW-28240F Set the port queue shaper rate in 1000 MGSW-28240F:/>qos Port QueueShaper rate 1-10 0-7 1000 QoS Port QueueShaper

User’s Manual of MGSW-28240F mapped : Use mapped versions of QoS class and DP level (default: Show port tag remarking mode) Default Setting:

User’s Manual of MGSW-28240F Parameters: <port_list>: Port list or 'all', default: All ports <dei> : Drop Eligible Indicat

User’s Manual of MGSW-28240F <port_list>: Port list or 'all', default: All ports enable : Enable DSCP ingress translation disable

User’s Manual of MGSW-28240F QoS Port DSCP EgressRemark Description: Set or show the port DSCP remarking mode. Syntax: QoS Port DSCP EgressRemark [&

User’s Manual of MGSW-28240F QoS DSCP Translation Description: Set or show global ingress DSCP translation table. If port DSCP translation is enabled

User’s Manual of MGSW-28240F If port DSCP classification is 'selected', DSCP will be classified based on QoS class and DP level only for DS

User’s Manual of MGSW-28240F enable : Enable unicast storm control disable : Disable unicast storm control <packet_rate>: Rate in fp

User’s Manual of MGSW-28240F Syntax: QoS Storm Broadcast [enable|disable] [<packet_rate>] Parameters: enable : Enable broadcast storm co

User’s Manual of MGSW-28240F 3.5 SNMP-Based Network Management You can use an external SNMP-based application to configure and manage the Managed S

User’s Manual of MGSW-28240F <etype> : Ethernet Type: 0x600-0xFFFF or 'any' but excluding 0x800(IPv4) and 0x86DD(IPv6) llc

User’s Manual of MGSW-28240F QoS QCL Lookup Description: Lookup QoS Control List. Syntax: QoS QCL Lookup [<qce_id>] Parameters: <qce_id>

User’s Manual of MGSW-28240F 552 the resource. Syntax: QoS QCL refresh Parameters: combined|static|voice_vlan|conflicts: combined : Shows

User’s Manual of MGSW-28240F 6.14 Mirror Command Mirror Configuration Description: Show mirror configuration. Syntax: Mirror Configuration [<port

User’s Manual of MGSW-28240F 554 Mirror Mode Description: Set or show the mirror mode. Syntax: Mirror Mode [<port_list>] [enable|disable|rx|

User’s Manual of MGSW-28240F 6.15 Configuration Command Configuration Save Description: Save configuration to TFTP server. Syntax: Config Save <i

User’s Manual of MGSW-28240F 6.16 Firmware Command Firmware Load Description: Load new firmware from TFTP server. Syntax: Firmware Load <ip_addr_

User’s Manual of MGSW-28240F Firmware Swap Description: Activate the alternate firmware image.. Syntax: Firmware Swap

User’s Manual of MGSW-28240F 6.17 UPnP Command UPnP Configuration Description: Show UPnP configuration. Syntax: UPnP Configuration Example: Show

User’s Manual of MGSW-28240F MGSW-28240F:/>upnp mode enable UPnP TTL Description: Set or show the TTL value of the IP header in SSDP messages.

User’s Manual of MGSW-28240F If there are two LAN cards or above in the same administrator PC, choose different LAN card by using the “Select Adapt

User’s Manual of MGSW-28240F 6.18 MVR Command MVR Configuration Description: Show the MVR configuration. Syntax: MVR Configuration Example: Show

User’s Manual of MGSW-28240F MVR Mode [enable|disable] Parameters: enable : Enable MVR mode disable : Disable MVR mode (default: Show MVR

User’s Manual of MGSW-28240F Parameters: <vid>|<mvr_name>: MVR VLAN ID (1-4095) or Name (Maximum of 32 characters) dynamic : Dynamic MV

User’s Manual of MGSW-28240F MVR VLAN Channel Description: Set or show per MVR VLAN channel. Syntax: MVR VLAN Channel [<vid>|<mvr_name>]

User’s Manual of MGSW-28240F MVR Immediate Leave [<port_list>] [enable|disable] Parameters: <<port_list>: Port list or 'all&apos

User’s Manual of MGSW-28240F MVR SFM [<vid>] [<port_list>] Parameters: <vid> : VLAN ID (1-4095) <port_list>: Port list

User’s Manual of MGSW-28240F 6.19 Voice VLAN Command Voice VLAN Configuration Description: Show Voice VLAN configuration. Syntax: Voice VLAN Configu

User’s Manual of MGSW-28240F Port Mode Security Discovery Protocol ---- -------- -------- ------------------ 1 Disabled Disabled OU

User’s Manual of MGSW-28240F Voice VLAN ID Description: Set or show Voice VLAN ID. Syntax: Voice VLAN ID [<vid>] Parameters: <vid>: VLA

User’s Manual of MGSW-28240F Voice VLAN Traffic Class Description: Set or show Voice VLAN ID. Syntax: Voice VLAN Traffic Class [<class>] Para

User’s Manual of MGSW-28240F 57 4. WEB CONFIGURATION This section introduces the configuration and functions of the Web-based management. About Web

User’s Manual of MGSW-28240F Voice VLAN OUI Delete Description: Delete Voice VLAN OUI entry. Modify OUI table will restart auto detect OUI process.

User’s Manual of MGSW-28240F Example: Lookup Voice VLAN OUI entry. MGSW-28240F:/>voice vlan oui lookup Voice VLAN Port Mode Description: Set

User’s Manual of MGSW-28240F Parameters: <port_list>: Port list or 'all', default: All ports enable : Enable Voice VLAN security mode

User’s Manual of MGSW-28240F 6.20 Loop Protect Command Loop Protect Configuration Description: Show Loop Protection configuration. Syntax: Loop Prot

User’s Manual of MGSW-28240F Loop Protect Shutdown Description: Set or show the Loop Protection shutdown time. Syntax: Loop Protect Shutdown [<sh

User’s Manual of MGSW-28240F Loop Protect Port Action Description: Set or show the Loop Protection port action. Syntax: Loop Protect Port Action [&l

User’s Manual of MGSW-28240F 6.21 IPMC Command IPMC Configuration Description: Show IPMC snooping configuration. Syntax: IPMC Configuration [mld|igm

User’s Manual of MGSW-28240F IPMC Flooding Description: Set or show the IPMC unregistered addresses flooding operation. Syntax: IPMC Flooding [mld|ig

User’s Manual of MGSW-28240F disable Example: Enable IGMP Leave Proxy MGSW-28240F:/>ipmc leave proxy igmp enable IPMC Proxy Description: Set

User’s Manual of MGSW-28240F Parameters: mld|igmp : mld : IPMC for IPv6 MLD igmp: IPMC for IPv4 IGMP range : SSM Range keyword <prefix> :

User’s Manual of MGSW-28240F  Logging on the Managed Switch 1. Use Internet Explorer 7.0 or above Web browser. Enter the factory-default IP addres

User’s Manual of MGSW-28240F IPMC State Description: Set or show the IPMC snooping state for VLAN. Syntax: IPMC State [mld|igmp] [<vid>] [enab

User’s Manual of MGSW-28240F Default Setting: disable Example: Enable IGMP querier for VLAN 1 MGSW-28240F:/>ipmc querier igmp 1 enable IPMC

User’s Manual of MGSW-28240F igmp: IPMC for IPv4 IGMP <port_list>: Port list or 'all', default: All ports enable : Enable MLD fast le

User’s Manual of MGSW-28240F IPMC Filtering Description: Set or show the IPMC port group filtering list. Syntax: IPMC Filtering [mld|igmp] [<port

User’s Manual of MGSW-28240F IPMC Status Description: Show IPMC operational status, accordingly. Syntax: IPMC Status [mld|igmp] [<vid>] Parame

User’s Manual of MGSW-28240F IPMC Version Description: Show IPMC Versions. Syntax: IPMC Version [mld|igmp] [<vid>] Parameters: mld|igmp: mld

User’s Manual of MGSW-28240F Syntax: IPMC Parameter RV [mld|igmp] [<vid>] [ipmc_param_rv] Parameters: mld|igmp : mld : IPMC for IPv6 MLD i

User’s Manual of MGSW-28240F Parameters: mld|igmp : mld : IPMC for IPv6 MLD igmp: IPMC for IPv4 IGMP <vid> : VLAN ID (1-4095) or &

User’s Manual of MGSW-28240F mld : IPMC for IPv6 MLD igmp: IPMC for IPv4 IGMP <vid> : VLAN ID (1-4095) or 'any', default: Sho

User’s Manual of MGSW-28240F 6.22 VLAN Control List Command VCL MAC-based VLAN Configuration Description: Show VCL MAC-based VLAN configuration. Syn

User’s Manual of MGSW-28240F Figure 4-1-3: Default Main Page Now, you can use the Web management interface to continue the switch management or man

User’s Manual of MGSW-28240F Delete 00-11-22-33-44-55-66 in MAC-based VLAN list MGSW-28240F:/> vcl macvlan del 00-11-22-33-44-55-66 VCL Stasus

User’s Manual of MGSW-28240F VCL Protocol-based VLAN Add LLC Description: Add VCL protocol-based VLAN LLC protocol to group mapping. Syntax: VCL Pro

User’s Manual of MGSW-28240F VCL Protocol-based VLAN Delete LLC Description: Delete VCL protocol-based VLAN LLC protocol to group mapping. Syntax: V

User’s Manual of MGSW-28240F VCL Protocol-based VLAN Configuration Description: Show VCL protocol-based VLAN entries. Syntax: VCL ProtoVlan Conf V

User’s Manual of MGSW-28240F Delete VCL IP Subnet-based VLAN entry. Syntax: VCL IPVlan Delete <vce_id> Parameters: <vce_id>: Unique VCE

User’s Manual of MGSW-28240F 6.23 SMTP Command SMTP Configuration Description: Show SMTP configure. Syntax: SMTP Configuration Default Setting: dis

User’s Manual of MGSW-28240F <server>: SMTP server address <port> : SMTP server port Default Setting: disable SMTP Auth Description:

User’s Manual of MGSW-28240F SMTP Auth_pass Description: Set or to show SMTP authentication password configure. Syntax: SMTP Auth_pass [<auth_pas

User’s Manual of MGSW-28240F Default Setting: Disable SMTP Mail to 1 Description: Set or show SMTP e-mail 1 to configure. Syntax: SMTP Mailto1 [<

User’s Manual of MGSW-28240F 6.24 DIDO Command DIDO DI Act Description: Set or show the system digital input0/1 action. Syntax: DIDO Di_act [first|s

User’s Manual of MGSW-28240F 4.8 Multicast...

User’s Manual of MGSW-28240F 60 4.1 Main Web Page The Managed Switch provides a Web-based browser interface for configuring and managing it. This i

User’s Manual of MGSW-28240F DIDO DI Enable Description: Set or show the system digital input0/1. Syntax: DIDO Di_en [first|second] [enable|disable]

User’s Manual of MGSW-28240F enable : Enable digital input0/1 function disable : Disable digital input0/1 function (default: Set or show digital inp

User’s Manual of MGSW-28240F DIDO DO Power Alarm Description: Set or show the system digital output0/1 power alarm. Syntax: DIDO Do_pwr_alr [first|s

User’s Manual of MGSW-28240F DIDO Fault Enable Description: Set or show the system fault alarm. Syntax: DIDO Fault_en [enable|disable] Parameters:

User’s Manual of MGSW-28240F (default: Set or show digital input/output/fault alarm 0/1 status) 6.25 Show Command Show Access Description: Show ac

User’s Manual of MGSW-28240F Show Auth Description: Show Auth configuration. Syntax: Show auth Show DHCP Relay Description: Show DHCP relay config

User’s Manual of MGSW-28240F Syntax: Show ip Show LACP Description: Show LACP configuration. Syntax: Show lacp Show Limit Control Description:

User’s Manual of MGSW-28240F Show Loop Protect Description: Show Loop Protection configuration. Syntax: Show Loop Protect Show MAC Description: Sh

User’s Manual of MGSW-28240F Syntax: Show port Show Privilege Description: Show privilege configuration. Syntax: Show privilege Show Private VL

User’s Manual of MGSW-28240F Show SSH Description: Show SSH configuration. Syntax: Show ssh Show System Description: Show system configuration. S

User’s Manual of MGSW-28240F Main Menu Using the onboard web agent, you can define system parameters, manage and control the Managed Switch, and al

User’s Manual of MGSW-28240F Syntax: Show users Show VLAN Description: Show VLAN configuration. Syntax: Show vlan Show Voice VLAN Description: S

User’s Manual of MGSW-28240F 6.26 MEP Command mep config Description: MEP instance configuration. Syntax: MEP config [<inst>] [mep|mip] [ingre

User’s Manual of MGSW-28240F Syntax: MEP peer MEP [<inst>] [<mep>] [<mac_addr>] [enable|disable] Parameters: <inst> :

User’s Manual of MGSW-28240F 6.27 ERPS Command erps add Description: Create a new ethernet ring protection group. <group-id> : protection gr

User’s Manual of MGSW-28240F Syntax: Erps mep <east_sf_mep> <west_sf_mep> <east_raps_mep> <west_raps_mep> <group-id> P

User’s Manual of MGSW-28240F Syntax: Erps rpl neighbour <rpl_port> <group-id> Erps rpl owner <rpl_port> <group-id> Erps rpl n

User’s Manual of MGSW-28240F erps guard-timeout Description: Configuring guard timeout for a protection group guard timeout should be configured in t

User’s Manual of MGSW-28240F Example: MGSW-28240F:/> erps wtr-timeout 1 1 erps delete Description: Deletion of a protection group. <group-i

User’s Manual of MGSW-28240F MGSW-28240F:/> erps topologychange nopropagate 1 erps configuration Description: Deletion of a protection group. &l

User’s Manual of MGSW-28240F 7. SWITCH OPERATION 7.1 Address Table The Managed Switch is implemented with an address table. This address table compos

User’s Manual of MGSW-28240F 4.2 System Use the System menu items to display and configure basic administrative details of the Managed Switch. Under

User’s Manual of MGSW-28240F 620 7.5 Auto-Negotiation The STP ports on the Managed Switch have built-in “Auto-negotiation”. This technology automat

User’s Manual of MGSW-28240F 8. TROUBLE SHOOTING This chapter contains information to help you solve problems. If the Managed Switch is not functioni

User’s Manual of MGSW-28240F  While IP Address be changed or forgotten admin password – To reset the IP address to the default IP Address “192.16

User’s Manual of MGSW-28240F 623 APPENDEX A A.1 Switch's Data RJ-45 Pin Assignments - 1000Mbps, 1000Base-T PIN NO MDI MDI-X 1 BI_DA+ BI_DB

User’s Manual of MGSW-28240F The standard cable, RJ-45 pin assignment The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP

User’s Manual of MGSW-28240F APPENDEX B: GLOSSARY A ACE ACE is an acronym for Access Control Entry. It describes access permission associated with

User’s Manual of MGSW-28240F Rate Limiter ID to the ACE(s) or ingress port(s). AES AES is an acronym for Advanced Encryption Standard. The encryp

User’s Manual of MGSW-28240F transmitting CCM frames to a peer MEP. CCM CCM is an acronym for Continuity Check Message. It is a OAM frame transmi

User’s Manual of MGSW-28240F The DHCP option 82 enables a DHCP relay agent to insert specific information into a DHCP request packets when forwarding

User’s Manual of MGSW-28240F E EPS EPS is an abbreviation for Ethernet Protection Switching defined in ITU/T G.8031. ERPS Ethernet Ring Protecti

User’s Manual of MGSW-28240F configured SNTP Server, if any. The period of time the device has been operational.  System Uptime  Software Version

User’s Manual of MGSW-28240F connection to a particular port on a remote host (port 80 by default). An HTTP server listening on that port waits for t

User’s Manual of MGSW-28240F from a mail server. IMAP is the protocol that IMAP clients use to communicate with the servers, and SMTP is the protoc

User’s Manual of MGSW-28240F LLC The IEEE 802.2 Logical Link Control (LLC) protocol provides a link mechanism for upper layer protocols. It is the

User’s Manual of MGSW-28240F MEP MEP is an acronym for Maintenance Entity Endpoint and is an endpoint in a Maintenance Entity Group (ITU-T Y.1731).

User’s Manual of MGSW-28240F NetBIOS is an acronym for Network Basic Input/Output System. It is a program that allows applications on separate comput

User’s Manual of MGSW-28240F PHY PHY is an abbreviation for Physical Interface Transceiver and is the device that implements the Ethernet physical

User’s Manual of MGSW-28240F configured as part of PVLAN cannot communicate with each other. Member ports of a PVLAN can communicate with each other.

User’s Manual of MGSW-28240F RARP is an acronym for Reverse Address Resolution Protocol. It is a protocol that is used to obtain an IP address for a

User’s Manual of MGSW-28240F SNAP The SubNetwork Access Protocol (SNAP) is a mechanism for multiplexing, on networks using IEEE 802.2 LLC, more pro

User’s Manual of MGSW-28240F T TACACS+ TACACS+ is an acronym for Terminal Acess Controller Access Control System Plus. It is a networking protocol

User’s Manual of MGSW-28240F The Current column is used to show the active IP configuration. Object Description Enable the DHCP client by checking t

User’s Manual of MGSW-28240F determine the priority from the 6-bit ToS field in the IP header. The most significant 6 bits of the ToS field are fully

User’s Manual of MGSW-28240F It is Virtual LAN. It is a method to restrict communication between switch ports. VLANs can be used for the following ap

User’s Manual of MGSW-28240F 642 necessarily with first generation wireless access points. WPA2 implements the full standard, but will not work wit

EC Declaration of Conformity For the following equipment: *Type of Product: MGSW-28240F *Model Number: 24-Port 100/1000Base-X SFP + 4-Port 10G SF

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  Auto Configuration Enable IPv6 auto-configuration by

User’s Manual of MGSW-28240F Figure 4-2-4: Users Configuration Page Screenshot The page includes the following fields: Object Description The name

User’s Manual of MGSW-28240F The page includes the following fields: Object Description A string identifying the user name that this entry should be

User’s Manual of MGSW-28240F 68 4.2.5 Privilege Levels This page provides an overview of the privilege levels. After setup is completed, please pre

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  Group Name The name identifying the privilege group. In m

User’s Manual of MGSW-28240F 4.10 Access Control Lists...

User’s Manual of MGSW-28240F 4.2.6 NTP Configuration Configure NTP on this page. NTP is an acronym for Network Time Protocol, a network protocol for

User’s Manual of MGSW-28240F 4.2.7 UPnP Configure UPnP on this page. UPnP is an acronym for Universal Plug and Play. The goals of UPnP are to allow d

User’s Manual of MGSW-28240F Figure 4-2-10: UPnP Devices shows on Windows My Network Places 4.2.8 DHCP Relay Configure DHCP Relay on this page. DH

User’s Manual of MGSW-28240F means the port number. The Remote ID is 6 bytes in length, and the value is equal the DHCP relay agent’s MAC address.

User’s Manual of MGSW-28240F  Keep: Keep the original relay information when receiving a DHCP message that already contains it.  Drop: Drop the

User’s Manual of MGSW-28240F  Receive Bad Remote ID The number of packets whose Remote ID option did not match known Remote ID. Client Statistics O

User’s Manual of MGSW-28240F Figure 4-2-13: CPU Load Page Screenshot Buttons Auto-refresh : Check this box to refresh the page automatically. Aut

User’s Manual of MGSW-28240F 4.2.11 System Log The switch system log information is provided here. The System Log screen in Figure 4-2-14 appears. F

User’s Manual of MGSW-28240F : Updates the system log entries, starting from the first available entry ID. : Updates the system log entries, ending a

User’s Manual of MGSW-28240F 79 : Click this button to print out system log. 4.2.13 Remote Syslog Configure remote syslog on this page. The Remot

User’s Manual of MGSW-28240F 4.14.2 LLDP Configuration ...

User’s Manual of MGSW-28240F 4.2.14 SMTP Configuration Configure SMTP Configuration on this page. The SMTP Configuration screen in Figure 4-2-17 appe

User’s Manual of MGSW-28240F  E-mail Subject It is for you to input mail subject.  E-mail 1 To It is for you to input recipient mail address. 

User’s Manual of MGSW-28240F The page includes the following fields: Object Description  Enable Checks the Enable checkbox will enable Digital Inp

User’s Manual of MGSW-28240F 4.2.16 Faulty Alarm The Faulty Relay Alarm function provides the Power Failure and Port Link Down/Broken detection. With

User’s Manual of MGSW-28240F 4.2.17 Web Firmware Upgrade This page facilitates an update of the firmware controlling the Managed Switch. The Web Firm

User’s Manual of MGSW-28240F 4.2.18 TFTP Firmware Upgrade The Firmware Upgrade page provides the functions to allow a user to update the Managed Swit

User’s Manual of MGSW-28240F Save configuration except IP Address feature is almost the same with Save configuration, except the IP address will not

User’s Manual of MGSW-28240F 2. Chose the file save path in management workstation. Figure 4-2-25: File Save Screen 4.2.20 Configuration Upload Th

User’s Manual of MGSW-28240F 88 Figure 4-2-27: Windows File Selection Menu Popup 2. Select on the configuration file and then click “”,.The bott

User’s Manual of MGSW-28240F 4.2.21 Image Select This function provides dual image deposit in the Managed Switch. User can select any one of the imag

User’s Manual of MGSW-28240F 6.1 System Command...

User’s Manual of MGSW-28240F Figure 4-2-31: Image Select Page Screenshot After the system reboot, you can use the Alternate Image of Managed Switch

User’s Manual of MGSW-28240F After the “Factory” button be pressed and rebooted, the system will be loaded default settings, except IP address. To

User’s Manual of MGSW-28240F 4.3 Simple Network Management Protocol 4.3.1 SNMP Overview The Simple Network Management Protocol (SNMP) is an applicati

User’s Manual of MGSW-28240F Configure SNMPv3 groups table on this page.  SNMPv3 Groups Configure SNMPv3 views table on this page.  SNMPv3 Views

User’s Manual of MGSW-28240F SNMP version is SNMPv3, the community string will be associated with SNMPv3 communities table. It provides more flexibil

User’s Manual of MGSW-28240F 95  Trap Destination Address Indicates the SNMP trap destination address. It allows a valid IP address in dotted dec

User’s Manual of MGSW-28240F 4.3.4 SNMP System Information The switch system information is provided here. The SNMP System Information screen in Figu

User’s Manual of MGSW-28240F 4.3.5 SNMPv3 Configuration 4.3.5.1 SNMPv3 Communities Configure SNMPv3 communities table on this page. The entry index k

User’s Manual of MGSW-28240F 4.3.5.2 SNMPv3 Users Configure SNMPv3 users table on this page. The entry index keys are Engine ID and User Name. The SN

User’s Manual of MGSW-28240F authentication protocol.  SHA: An optional flag to indicate that this user using SHA authentication protocol.  T